Designed for industrial environments where elevated relative humidity challenges conventional sensing equipment.
High moisture levels can make continuous temperature and humidity monitoring difficult, particularly in processing rooms, drying equipment and other humid industrial environments. The HENGKO HG808-H is designed for high-humidity monitoring applications, with industrial probe configurations and multiple signal output options.
Its combination of temperature, relative humidity and calculated dew-point data helps engineers monitor process conditions and identify conditions that may increase condensation risk.
*The stated high-humidity design target is not a verified continuous condensing-operation rating. Confirm the allowable operating envelope for the selected probe.
As relative humidity approaches saturation, small temperature differences between the air, probe and surrounding surfaces can increase the likelihood of condensation. Water droplets on a sensing element may affect measurement recovery, accuracy and long-term reliability.
Long periods of elevated humidity can place greater demands on sensor protection and maintenance.
Rapid changes in process conditions can influence sensor response and the risk of localized condensation.
Probe placement, cable routing, process temperature and maintenance access all affect measurement system design.
The HG808-H is positioned for humid industrial environments, including applications with relative humidity approaching the upper end of the measurement range. Continuous exposure and condensation tolerance should be confirmed for the selected probe.
Available probe assemblies incorporate protective metal structures. The exact filter material, pore structure and environmental protection depend on the chosen configuration.
The original product information lists ESD and reverse-polarity protection, supporting integration into industrial monitoring systems.
The HG808-H combines measured temperature and relative humidity with calculated moisture-related parameters for process monitoring and control system integration.
Temperature data helps characterize the thermal conditions surrounding the sensor. The supplied technical table specifies a −40 to +100°C measurement range; other temperature claims require model-specific confirmation.
The technical table lists a 0–100% RH measurement range and recommends operation below 95% RH. The separate 95–98% RH durability claim needs a defined continuous operating condition.
Calculated dew-point temperature provides another way to interpret moisture conditions. Comparing dew point with surface temperature can help identify potential condensation conditions.
The product supports RS485 Modbus RTU communication and analog output configurations for temperature and humidity, allowing integration with compatible PLC, DCS and SCADA systems.
The following data follows the supplied product specification table. Some values should be confirmed for the HG808-H variant rather than assumed to apply to every HG808 probe.
| Measurement Performance | |
|---|---|
| Temperature Range | −40 to +100°C (datasheet reference) |
| Humidity Range | 0–100% RH; recommended below 95% RH |
| Temperature Accuracy | ±0.1°C at 20°C |
| Humidity Accuracy | ±2% RH at 20°C, 10–90% RH |
| Resolution | Temperature: 0.01 / 0.1°C; RH: 0.01 / 0.1% RH |
| Electrical & Communication | |
| Power Supply | DC 10–28 V |
| Power Consumption | Less than 0.5 W |
| Analog Output | Temperature and RH; selectable 4–20 mA, 0–5 V or 0–10 V configuration |
| RS485 Modbus RTU | Temperature, RH, dew point and PPM data |
| Baud Rate | 1200 / 2400 / 4800 / 9600 / 19200 / 115200 bps; default 9600 |
| Serial Format | 8 data bits, no parity, 1 stop bit |
| Acquisition Interval | Fastest listed: 1 second |
| Environmental & Installation | |
| Electronics Operating Environment | −20 to +60°C; 0–95% RH, non-condensing |
| Pressure Rating | 16 bar listed; verify probe-specific suitability |
| Probe Families | 0A/0B, 3A/3B, 5A/5B, 6A/6B listed in supplied table |
HG808-series probe options include split and pipeline configurations. The selected probe should match the installation geometry, process conditions and service requirements.
Allow the sensing probe to be positioned separately from the transmitter electronics, depending on the selected assembly.
Designed for insertion into compatible pipe or duct measurement locations using the specified mounting arrangement.
Images illustrate HG808-series probe styles. Confirm which configurations are available specifically for HG808-H.
Select the communication interface according to the receiving equipment. The analog configuration provides temperature and humidity signals, while RS485 Modbus RTU allows compatible systems to read multiple measurement values digitally.
Digital communication for temperature, relative humidity, calculated dew point and PPM values. Confirm register mapping, scaling and device address settings before integration.
4–20 mA, 0–5 V and 0–10 V configurations are listed. The selected analog output type should be specified at ordering.
Always follow the wiring diagram supplied with the exact purchased model. Wire colors and terminal assignments may differ by configuration.
The original product list separates HG808-H transmitters with local display from models without a display. Use the model charts below to identify the intended ordering configuration.
When requesting a quotation, include the desired probe, display option, analog output type, RS485 requirements, cable length and estimated purchase quantity.
The HG808-H is intended for industrial environments where humidity monitoring remains important during elevated moisture conditions. Application suitability depends on the actual temperature, humidity, condensation and chemical exposure.
Monitor temperature and humidity in suitable processing rooms, conditioning areas and humid production environments where moisture variations affect process control.
Track changes in humidity and temperature during drying or conditioning operations within the selected probe's validated operating range.
Monitor moisture conditions in compatible fermentation-related spaces and industrial environments, subject to cleaning and material compatibility requirements.
Provide environmental monitoring data for suitable manufacturing or utility areas. Qualification, calibration and regulatory compliance requirements must be assessed separately.
Monitor temperature and humidity where moisture conditions are relevant to equipment or process operation. Exposure to corrosive vapors requires specific probe compatibility verification.
The original description identifies 95–98% RH as a high-humidity design target. However, the specification table recommends below 95% RH. Continuous exposure limits, condensation tolerance and performance stability must be confirmed.
High relative humidity does not automatically mean compatibility with saturated steam, liquid water immersion or direct spray. These conditions require separate protection and temperature verification.
Yes. The supplied technical information lists RS485 Modbus RTU for reading temperature, humidity, dew point and PPM data.
Yes. The supplied product list includes versions with and without a local display. Confirm the required probe and output combination when ordering.
Select a location representative of the process, avoid unnecessary liquid water accumulation, consider maintenance access and keep transmitter electronics within their specified ambient conditions.
Share your temperature range, normal and peak RH, condensation conditions, probe installation method and output requirements. HENGKO can help review the appropriate HG808-H configuration.
Request Technical Support & Quote
Email: ka@hengko.com